球迷网

當前位置:首頁-常見問題解答>>激光全息防偽標簽的特點有哪些?

激光全息防偽標簽的特點有哪些?

來源:http://tjanamera.com/ 日期:2021-01-31 發布人:shengfeng 一、標識外觀圖案觀察:
1、 Logo appearance pattern observation:
激光防偽標識圖案觀察,須手持激光標識于點光源下觀看。如陽光、白熾燈光下,會看到明亮、清晰的圖案(如陰天或熒光光源下會呈現出不清晰的圖案),如果點光源下一開始看不清圖案,則需轉、移動激光標識角度,直到看清為止。
To observe the laser anti-counterfeiting logo pattern, it is necessary to hold the laser logo under the point light source. For example, bright and clear patterns can be seen under sunlight and incandescent light (for example, unclear patterns can be seen under cloudy day or fluorescent light). If the pattern cannot be seen clearly at first under the point light source, it is necessary to turn and move the laser marking angle until it is clear.
二、激光全息防偽的粘貼:
2、 Laser holographic anti-counterfeiting paste:
A、激光全息防偽標識粘貼在表面光滑、平整、清潔的防粘底紙上(特殊產品需要采用專用的膠水制作,客戶在下訂單前溝通清楚標識被粘物)。
A. The laser holographic anti-counterfeiting logo is pasted on the anti sticking backing paper with smooth, flat and clean surface (special products need to be made with special glue, and the customer should communicate clearly to identify the stuck object before placing the order).
B、從防粘底紙上提取防偽標識時,應把防粘底紙向背面沿待取防偽標識的邊緣直線折疊一部分,使防偽標識自動從防粘紙上翹起一部分。
B. When the anti-counterfeiting label is extracted from the anti-counterfeiting backing paper, the anti-counterfeiting backing paper should be folded to the back along the edge of the anti-counterfeiting label to be taken, so that the anti-counterfeiting label will automatically tilt up from the anti-counterfeiting label.
激光標簽制作廠家
C、從防粘紙上提取翹起的標識時,手要清潔干凈,不能帶有灰塵、油污、水漬等,手與防偽標識的底層涂膠面接觸不宜太大,且拿捏用力適中,以免損壞標識的底層粘度;提取防偽標識時,應遵循正常揭啟規律,不得強行拉拽,且速度不宜太快,太快則易損傷防偽標識;嚴禁直接從防粘紙上摳起防偽標識。
C. When extracting the cocked logo from the anti-counterfeiting paper, the hand should be clean, without dust, oil, water stains, etc. the contact between the hand and the bottom gluing surface of the anti-counterfeiting logo should not be too big, and the holding force should be moderate, so as not to damage the bottom viscosity of the logo. When extracting the anti-counterfeiting logo, the normal opening law should be followed, and it should not be forced to pull, and the speed should not be too fast, too fast will easily damage the anti-counterfeiting It is strictly forbidden to pick up the anti-counterfeiting mark directly from the anti sticking paper.
D、粘貼防偽標識時,被貼物表面要清潔干凈,禁忌灰塵、油污和水漬等;當標識貼到被貼物表面時,應用手指用力將防偽標識壓平整,使防偽標識與被貼物表面充分粘合。
D. When pasting the anti-counterfeiting label, the surface of the pasted object should be clean, and dust, oil and water stains are forbidden; when the label is pasted on the surface of the pasted object, the finger should be used to press the anti-counterfeiting label flat, so as to make the anti-counterfeiting label fully adhere to the surface of the pasted object.
三、激光防偽標識的使用:
3、 Use of laser anti-counterfeiting label:
A、揭開式激光全息圖案防偽標識使用:一次性揭開式激光全息圖案防偽標識在揭啟時,應用手指甲沿標識的邊緣某部位揭起,手指捏緊被揭起部位,再用力撕揭,全息圖像應殘留/部分殘留在被貼物表面上/標識的平整度被破壞,無法再重復使用。
A. Use of unveiling laser holographic pattern anti-counterfeiting logo: when unveiling the one-time unveiling laser holographic pattern anti-counterfeiting logo, the fingernail should be lifted along the edge of the logo, the finger should pinch the uncovered part, and then tear it hard. The holographic image should be left / partially left on the surface of the pasted object / the flatness of the logo is damaged and cannot be reused.
B、刮開式標識使用:刮開式電話電碼防偽標識在刮開覆蓋墨時,先試探性刮一下,再決定用力大小,切勿一開始用力過大,損傷覆蓋墨下面的數碼,如個別標識覆蓋墨難以刮開時,可稍微加水浸潤一下,半小時再刮。
B. Use of scrape open label: when scraping off the cover ink of the scrape open telephone code anti-counterfeiting label, try to scrape it first, and then determine the force. Do not use too much force at the beginning to damage the numbers under the cover ink. If it is difficult to scrape off the cover ink of individual labels, you can add a little water and then scrape it for half an hour.
C、揭開式標識使用:揭開式電話電碼防偽標識揭啟時,應首先確認表層圖案的提示語言,再按提示從正確位置揭啟。用手指甲輕輕揭起標識邊緣部分,手指捏緊被揭起部位,再慢慢揭開(切勿用力過猛,以防損傷底層),底層留在被貼物上,底層/表面背面的數碼應完整并易于辨認。
C. Use of unveiling signs: when unveiling the unveiling telephone code anti-counterfeiting signs, the prompt language of the surface pattern should be confirmed first, and then unveiling from the correct position according to the prompt. Gently lift the edge of the logo with fingernails, pinch the lifted part with fingers, and then slowly lift it (do not use too much force to prevent damage to the bottom layer). The bottom layer is left on the pasted object, and the number on the back of the bottom layer / surface should be complete and easy to identify.
以上就是激光標簽制作廠家http://tjanamera.com為大家介紹的內容,感謝您在百忙之中查看我公司的信息內容,如果您想要了解的更多,歡迎您來電進行咨詢!
These are laser label manufacturers http://tjanamera.com Thank you for checking our company's information in your busy schedule. If you want to know more, you are welcome to inquire!

上一篇:印刷醫藥標簽需要進行哪些步驟?
下一篇:標簽印刷制版應該注意什么?
聯系我們